Ghost Controls Keypad & Intercom Repair Nationwide

Ghost Controls Keypad & Intercom Repair: The Tampa Owner’s Guide

Ghost Controls keypad and intercom repair in Tampa typically runs $160 to $390 installed, depending on whether we’re replacing the keypad module, the intercom board, or the full entry station. We carry Ghost Controls-compatible keypads and intercom components on our trucks, so the swap is usually done in one visit. Most owners discover the failure the hard way: the keypad lights up but the gate won’t move, or a guest calls through the intercom and hears nothing but static on the other end. Either way, the part stops doing its only job, which is letting people in when you want them in.

Call (850) 533-8293

We replace keypads, intercom modules, and the wiring between them. If the issue is a blown keypad membrane or a corroded intercom board, you don’t need a new operator. You need the right Ghost Controls part, matched to your model, installed by someone who does it for a living.

Key Takeaways

• Typical keypad replacement in Tampa runs $160 to $280 installed; intercom module replacement runs $180 to $300; combined entry station work runs $250 to $390.
• The price is written down and agreed before we open anything up. It does not move at the door.
• We stock Ghost Controls-compatible keypads and intercom parts on the truck, and we can get specific boards or modules same-week when needed.
• Florida humidity and salt air are rough on keypad membranes and intercom boards. We’ll match the part and seal it for the climate we actually live in.
• Carver Gate Repair Tampa is an independent service provider. We are not affiliated with Ghost Controls, and that’s fine. We work with their equipment daily.

Which Ghost Controls Models This Applies To

Our keypad and intercom repair work covers the Ghost Controls gate opener lines most common in Tampa: the AXP, AXR, and TSS series, along with the GhostControls wireless keypad kits and the wired intercom stations paired with those operators. If you have a Ghost Controls system and a keypad or intercom that has stopped responding, the repair path is usually the same: identify the part number on the back of the keypad or the bottom of the intercom housing, match it to the series, and swap the failed component. If the label is faded, we can identify it by voltage and connector type on-site.

One Ghost Controls-specific gotcha to know: their wireless keypads use rolling-code transmission, just like the remotes. That means a replacement keypad must be paired to the operator’s receiver, not just wired in and left alone. If a keypad is replaced without proper pairing, it looks installed but does nothing. We see this often enough that we check it on every keypad call. On the intercom side, the wiring is low-voltage, but Tampa’s humidity gets into the connector blocks and corrodes them slowly. A new module on old corroded wiring fails again within a year. We replace the connector and clean the termination points when the corrosion is advanced.

The OEM-versus-aftermarket decision for Ghost Controls parts is straightforward: for keypads, a quality aftermarket unit matched to the series works fine and saves money. For intercom boards, we use OEM or exact-spec replacements. The boards handle audio and call signaling on one circuit, and a generic board that doesn’t match the series will leave the call button dead or the audio faint. We’re not going to install a part that sets you up for another failure.

Signs Your Ghost Controls Keypad & Intercom Repair Is Failing

• The keypad lights up, but the gate doesn’t move. This is the classic dead-transmitter symptom. The keypad has power, but the rolling-code signal isn’t reaching the receiver. Re-pairing may fix it once; if it returns, the keypad module is done.
• One or more buttons stop responding. Ghost Controls keypads use a membrane layer under the buttons. Florida heat breaks that membrane down over time, and once one button goes dead, the rest follow.
• The gate opens by remote, but not by keypad. If remotes work and the keypad doesn’t, the issue is isolated to the keypad itself or its pairing. That’s the fastest diagnosis on the board: one component, one fix.
• The intercom rings through, but you can’t hear the visitor. This is almost always the speaker or audio circuit on the intercom board. Humidity is the usual culprit. A simple board swap restores the audio.
• The call button feels soft or won’t click. The tactile button under the faceplate wears out. The intercom still works for answering, but guests can’t actually call. It’s a small part with a big effect.

Replacement Cost & What’s Included

In Tampa, a Ghost Controls keypad replacement runs $160 to $280 installed; an intercom module replacement runs $180 to $300. If both need replacing, expect $250 to $390 total. The range depends on which series you have, whether the existing wiring is reusable, and whether we’re doing a single component or the full entry station. We quote the price before any work starts, and the number stays where it is.

Every keypad and intercom repair includes the part, the install, pairing or wiring, a connector inspection, and cleanup. It also comes with our 365-Day Done Right Promise in writing. If the repair fails within a year of the service date, we return and fix it free. That’s not a marketing line; that’s the policy that governs every job we run in Tampa.

DIY or Call Us?

There’s one thing an owner can safely check, and a couple of things you shouldn’t touch. On the keypad, check the batteries and verify the unit still lights up. If it doesn’t, fresh batteries solve it sometimes. If it does light up but still won’t open the gate, the pairing or the transmitter has failed, and that’s where a specialist’s time is cheaper than a homeowner’s guess.

The intercom side is low-voltage, but you’re working on a board that carries call signaling and audio together. Probe the wrong two pins and the board shorts. If you have a multimeter and know how to ring out continuity, you can check the wiring path. If you don’t, don’t. What should take one service call can turn into a dead board and a second trip. Call us at (850) 533-8293 and let us put eyes on it.

FAQs

Call Carver Gate Repair Tampa

If your Ghost Controls keypad or intercom has failed, call us at (850) 533-8293. A live person answers. We’ll schedule a window, show up in a marked truck, hand you a written price, and handle the repair the same visit in most cases. Lonnie Burke leads the crew, and the standard is what it has been for years: show up, do the job right, leave the site cleaner than you found it. That’s The Garrison Standard. That’s how we work in Tampa.

Written by Lonnie Burke, Owner, Carver Gate Repair Tampa at Carver Gate Repair Tampa, serving Tampa and nearby areas.